Hyundai Veloster Bushings
We source bushings for every Veloster generation sold in South Africa, then check the fit against your VIN before it leaves the warehouse
What Are Hyundai Veloster Bushings?
Bushes are the rubber or polyurethane isolators sitting between the suspension arms and the shell — control-arm, anti-roll-bar, subframe and engine-mount bushes all count. Where Hyundai bush sourcing gets interesting is that the front geometry changed within model names rather than between them: the LM and TL Tucson do not share arms, and the Getz TB, Accent LC and Accent RB are three different front ends despite living in the same showroom for years. Give us the generation code and the bush becomes a five-minute lookup instead of a guess.
Signs You Need New Bushings
Veloster generations and bushings — the short version
Veloster owners are usually surprised by how much turns on the generation code — FS, then JS all sold here.The asymmetric three-door layout means the left and right sides are genuinely not mirror images — door, glass and trim parts must be ordered by side.
Engine families fitted to the SA-market Veloster:
South African road surfaces punish suspension harder than the markets these cars were tuned for, and the SUVs in the range carry noticeably different rear geometry between two-wheel- and all-wheel-drive derivatives.
Send us the generation code and whether the car is front- or all-wheel drive with your enquiry and we will confirm the correct bushings against your car before anything is dispatched.
In South Africa the Veloster is mostly a low-volume enthusiast car locally, so mechanical parts come easily through the shared Gamma engine family while body and trim need specialist sourcing. That is the wear pattern we stock and source against.
Veloster Bushings: Common Questions
Will bushings from another Veloster fit mine?
Not automatically. The Veloster sold in South Africa as FS, then JS, and the asymmetric three-door layout means the left and right sides are genuinely not mirror images — door, glass and trim parts must be ordered by side. Send us the generation code off your VIN plate and we will confirm it either way before anything is dispatched.
Can you source bushings for the Veloster if local stock is dry?
Usually, yes. The Veloster shares its Gamma GDi and T-GDi engines with the i30 and Elantra of the same era, which gives us a second catalogue to search when Hyundai-listed stock runs out. We will tell you what we are quoting rather than leaving you to guess.
What are the symptoms of worn Hyundai bushings?
Clunks over bumps, wandering steering, uneven tyre wear and a clonk when you engage gear are the classics. Hyundai Forums documents the issue across Getz, i20, Accent, Sonata, Tucson and Creta — the front lower control-arm rear bush is the headline failure point.
How much does it cost to replace bushings on a Hyundai?
Parts span a wide range — budget rubber from around R150 up to polyurethane kits at R2,600 at SA pricing. Labour depends on location; subframe bushings are an hour each, engine mounts two to three. Send your VIN for a parts quote.
How long do Hyundai suspension bushings last?
Front control-arm rubber bushes typically last 80,000 to 140,000 km in SA conditions. Rear trailing-arm bushes last longer. Potholes and heavy loads shorten life dramatically; if you've hit a big pothole, check the bushes regardless of mileage.
Why does my Hyundai make a clunking noise over bumps?
Worn control-arm or anti-roll-bar bushes are the top suspects, especially on Getz, i20, Accent and Creta. Broken drop links and top-mount bearings mimic the symptom. We start with a hoist check of all front bushings — it's a ten-minute diagnosis.
Should I replace bushings with rubber or polyurethane?
OEM rubber is quieter and cheaper — R150-ish at SA retail. Polyurethane is stiffer, lasts longer and transmits more road noise — an i20 N owner might prefer it, a daily Tucson driver will not. For typical SA daily use we recommend OEM-spec rubber.
Tell us which Veloster you have
The Veloster sold here as FS, then JS, and they do not share one parts list. Give us the generation code and we will do the rest.