Hyundai Veloster Tie Rods
Tie Rods for the Hyundai Veloster — new, used and aftermarket stock, quoted once we know which Veloster you are running
What Are Hyundai Veloster Tie Rods?
Tie rods carry rack movement out to the wheel: an inner rod threaded into the rack itself, and an outer end at the knuckle. Which rack you have changes the part. The older hydraulically assisted Hyundais — the Getz, the earlier Accent and Atos, the Terracan — use a different arrangement to the newer electrically assisted cars where the motor sits on the column or the rack. Outer ends nearly always go first, and they announce themselves: the boot splits, the grease escapes, and the joint knocks on lock. Once the boot is open the clock is running, whatever the mileage says.
Signs You Need New Tie Rods
Before you order tie rods for a Veloster
Sold here across FS, then JS, the Veloster is not one car for parts purposes — it is several.The asymmetric three-door layout means the left and right sides are genuinely not mirror images — door, glass and trim parts must be ordered by side.
Engine families fitted to the SA-market Veloster:
South African road surfaces punish suspension harder than the markets these cars were tuned for, and the SUVs in the range carry noticeably different rear geometry between two-wheel- and all-wheel-drive derivatives.
Send us the generation code and whether the car is front- or all-wheel drive with your enquiry and we will confirm the correct tie rods against your car before anything is dispatched.
In South Africa the Veloster is mostly a low-volume enthusiast car locally, so mechanical parts come easily through the shared Gamma engine family while body and trim need specialist sourcing. That is the wear pattern we stock and source against.
Hyundai Veloster Tie Rods FAQs
Will tie rods from another Veloster fit mine?
Not automatically. The Veloster sold in South Africa as FS, then JS, and the asymmetric three-door layout means the left and right sides are genuinely not mirror images — door, glass and trim parts must be ordered by side. Send us the generation code off your VIN plate and we will confirm it either way before anything is dispatched.
What should I send you when asking about Veloster tie rods?
The VIN is the single most useful thing — a photo of the plate is fine. Failing that, the generation code and the engine code off the block. The Veloster ran as FS, then JS, so the generation is what narrows the search.
Inner or outer tie rod — which has gone?
The outer, usually. It screws onto the inner and connects to the wheel knuckle, and it is exposed, so its ball joint boot splits and the grease escapes. Inners thread into the rack under the rubber gaiter and generally only fail once that gaiter has torn and let dirt in. Two different parts and two different jobs.
How do I check a tie rod end on a Hyundai?
Grab the tyre at 9 and 3 o'clock and rock it firmly. Play with a knock means an outer tie rod, an inner CV joint or a lower ball joint — the test narrows it to three, and a hoist inspection settles which. Supporting symptoms are a clunk on turns, feathered front tyre wear and a squeak at parking speeds.
What does a tie rod end cost for a Hyundai?
Our supplier network stocks Hyundai Getz, Accent and Tucson right-hand tie rod ends from around R240. Do them in pairs. Request a free quote with your model and generation for both-sides parts plus fitting and the alignment.
Is a worn tie rod safe to drive on?
At low speed for a short time, yes. Beyond that, no — a worn tie rod can separate at the ball joint, and losing steering on one wheel at motorway speed is a crash rather than a breakdown. Book it within a week of noticing the clunk, not within a month.
Does the car need aligning afterwards?
Always. The tie rod sets the toe angle, so disturbing it means a four-wheel alignment to reset. Skip it and the new tyres are scrubbed out within weeks and the car pulls constantly. Build the alignment into the quote from the start rather than treating it as optional.
Get your Veloster tie rods matched properly
A part number from the old unit, or simply your VIN, is enough for us to identify the right tie rods for your Veloster.